Pontiac 400 TurnKey Engine
400HP $8300
Fully Prepared & Machined Pontiac 400 Block
%20(Copy%201).jpg)
(Before Machining)
Magnafluxed & Inspected for defects.
Mains Align Honed - Cylinders Bored & Torque Plate Honed - Decks Surfaced Straight and Parallel
Bolt Holes Thread Chased & Debured, Lifter Bores Polished, Pressure Washed, Rust Protection Coated.
Steel Gallery Plugs, Brass Freeze Plugs, Clevite 77 Cam Bearings, Painted with High Temp Paint in Your Choice of color
.jpg)
Reground Cast Iron Crankshaft.
|
Rebuilt Rods with ARP Bolts |
Clevite77 Bearings
Plasma Moly File Fit Rings |
High Performance Pistons
|
.jpg)
Hydraulic Camshaft & Lifters
A Set Of Edelbrock Performer RPM Heads
Designed for 1965-79 389-455 c.i.d. Pontiac engines, this head is patterned after the 1969-70 Ram Air IV Pontiac cylinder head. It produces outstanding horsepower with excellent low speed torque and throttle response. It's assembled with stainless steel, one-piece, swirl-polished 2.11 in. intake and 1.66 in. exhaust valves with under-cut stems to promote excellent flow for more power. Other features include 2-ring positive oil control seals, rocker studs and guideplates, valve springs, steel retainers, and keepers. It also includes bronze guides, hardened valve seats, and a 5/8 in. thick deck surface for superior durability and head gasket retention. All factory accessory bosses are included for bolt-on convenience.
Heavy Duty True Roller Timing Set New High Performance Harmonic Balancer
Chrome Moly pushrods New 1.7:1 Rocker Arms Roller Upgrades Available
Complete Fel-pro Gasket set Melling High Volume Oil pump
Oil Filter, Dipstick and Diptube All New Bolts
New Chrome Oil pan, Timing Cover, Baffled Valve Covers & Reclaimed Valley Pan
New Flexplate for Automatic Trans. (Standard Flywheel ask for price)
Balanced - Clearanced - Carefully Assembled
Edelbrock Performer Manifold 
See Manifold options Below
Edelbrock 4 barrel Carburetor with electric choke 
Designed and calibrated for optimum street performance in high-horsepower small-block and big-block engines. Match with a variety of manifolds that include Edelbrock Performer, Performer RPM, RPM Air-Gap, Torker II and others of a similar design. Includes the following
TPC Custom Carb upgrade available
New Fuel Pump and fuel lines 14 Inch Chrome Air Cleaner
PCV Ventilation System
High Energy Ignition Distributor with Integral 53,000 volt coil Pak
New AC Delco Spark Plugs gapped and installed Taylor 8mm Heat Resistant Silicone Wires
New High Flow Water pump New Chrome Thermostat Housing
Oil Filter, Dipstick and Diptube
Ready to Go!
For your convenience and confidence Your Engine run to break in the camshaft and rings.
The Ignition & Carburetor are Checked, Adjusted, Tune & Tested.
A Video will be Provided to You of the Engine being Run during this Process.
Your Engine is then Packaged and Crated for Shipment to YOU!
Manifold Options
|
Pre-Start Option $200
|
ENGINE BROKEN IN FOR 40 MINUTES
2 OIL FILTERS - OIL - GASOLINE - LABOR
THIRTY DAY WARRANTY ($100 Value) |
|
REAR WHEEL DYNO-TUNED $300
TUNED AND TESTED FOR POWER
ON THE CHASSIS DYNAMOMETER
ENGINE BROKEN IN FOR 40 MINUTES
2 OIL FILTERS - OIL - GASOLINE - LABOR
THREE MONTH WARRANTY ($150 Value)
|
FLYWHEEL DYNO-TUNED $600
ENGINE BROKEN IN FOR 40 MINUTES
ON THE ENGINE DYNAMOMETER
TUNED AND TESTED FOR POWER
ENGINE BROKEN IN FOR 40 MINUTES
2 OIL FILTERS - OIL - GASOLINE - LABOR
TWELVE MONTH WARRANTY ($200 Value) |
.jpg',108,64,'/t//Trucks_(resized).jpg',100,59))
)
